Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
- 2. Maintenance service
   2.1. Additional maintenance service
   2.2. Technical characteristics
   2.3. An arrangement of units in a motor compartment
   2.4. Maintenance service terms
   + 2.5. Check of level of liquids
   2.6. Check of a condition of tyres and pressure in tyres
   2.7. Liquid level in automatic transmission
   2.8. Liquid level in system of a hydrodrive of a steering
   2.9. Oil replacement in the engine and the oil filter
   2.10. Check of a condition and care of the battery
   2.11. Check of system of cooling
   2.12. Check and replacement of hoses in a motor compartment
   2.13. Check and replacement of brushes of a cleaner of a windscreen
   2.14. Shift of wheels
   2.15. Suspension bracket and steering check
   2.16. Exhaust system check
   2.17. Check of level of oil in a manual transmission
   2.18. Check of level of oil in a distributing box
   2.19. Check of level of oil in reducers of bridges
   2.20. Check of a condition of seat belts
   2.21. The thermostat of the air filter (carburettor engines)
   2.22. Check and greasing of the exhaust valve
   2.23. System of catching of steams of gasoline
   2.24. System check recycling
   2.25. Air заслонка the carburettor
   2.26. A zolotnik of system of ventilation картера
   2.27. Check and replacement of the air filter
   2.28. Replacement of spark plugs
   2.29. Check and adjustment of backlashes of valves
   2.30. Idling turns (carburettor engines)
   2.31. Drive belts
   2.32. Check of fuel system
   - 2.33. Check of brakes
      2.33.1. Check of the vacuum amplifier
      2.33.2. A manual brake
   2.34. Check and adjustment of pedals of coupling (brake)
   2.35. Replacement of the fuel filter
   2.36. High-voltage wires, бегунок and distributor covers
   2.37. Check and installation of the moment of ignition
   2.38. Care of cooling system
   2.39. Naves and bearings of forward wheels
   2.40. Liquid replacement in automatic transmission and the filter
   2.41. Oil replacement in a manual transmission
   2.42. Oil replacement in a distributing box
   2.43. Oil replacement in a back (forward) reducer
   2.44. Backlashes in valves on the engine 1FZ-FE
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


122d58df

2.33. Check of brakes
PERFORMANCE ORDER
1. Lift the car and remove wheels.
Check of disk brakes
2. Колодки it is possible to check up through a window in a support (it is specified by an arrow).
3. Measure a thickness of frictional overlays, and if a thickness less specified in subsection 8.1 replace Pads.
4. If there are any doubts concerning a normal state of overlays Pads it is necessary to remove.
5. At the same time measure a thickness of a disk and check up a surface condition (irrespective of its thickness). If the thickness is less than norm a disk replace. Insignificant defects of a surface leave the polishing, strongly worn out disk replace.
6. Check up a hose condition (the check place is specified by an arrow) and tubes of a hydrodrive of brakes. Check up reliability of an inhaling of connections, absence of contact with moving parts. All found out defects immediately eliminate.
Check of drum-type brakes
7. Remove drums (subsection 8.6 see).
8. Check up a thickness () frictional overlays. If their thickness (or distance to heads of rivets) is less 1,6 mm, or there are traces замасливания or serious damages Pads replace.
9. Check up a condition of springs and a backlash regulator between колодками and drums.
10. Check up подтекание liquids from the wheel cylinder, having unbent a dustproof cover. At detection of a leak the cylinder replace.
11. Check up a condition of drums. Minor defects polish a skin, if necessary drums pierce.
12. Establish all removed details and lower the car. Wheel nuts tighten with the set moment.