Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Kinds of repair without engine dismantle
      3.1.3. Installation of the piston of 1st cylinder in ВМТ
      3.1.4. A cover of a head of cylinders
      3.1.5. A lateral cover of the mechanism timing
      3.1.6. Коромысла and bars of pushers
      3.1.7. Springs of valves, plates, маслосъемные caps
      3.1.8. Soaking up and final collectors
      3.1.9. A head of cylinders
      3.1.10. Pushers
      3.1.11. A pulley коленвала
      3.1.12. A forward epiploon коленвала
      3.1.13. A forward cover
      3.1.14. A cam-shaft and drive gear wheels
      3.1.15. A cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. The oil pallet
      3.1.18. The oil pump
      3.1.19. A flywheel (a leading disk of the hydrotransformer)
      3.1.20. A back epiploon коленвала
      3.1.21. Suspension bracket and engine details
   + 3.2. The verhneklapannyj engine 1FZ-FE
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


122d58df

3.1.9. A head of cylinders
THE GENERAL DATA

Head of cylinders of the engine 2F

1. A spring and the valve
2. A lining
3. A pusher bar
4. Коромысла with platens
5. A cover
6. A candle
7. Inlet and final collectors
8. A system cooler recycling
9. A guard

10. The valve recycling
11. The generator
12. The thermostat
13. Vacuum tubes
14. An air branch pipe
15. A gasoline-supply line
16. A hose маслоохладителя
17. An exhaust pipe
18. A drain stopper

Head of cylinders of the engine 3F-E

1, 4. A rack of the chamber of an air inlet
2. The air inlet chamber
3. A tube of a starting atomizer
5. A tube recycling
6. An air branch pipe
7. The union
8. Gasoline-supply line N1 with a hook for engine posting
9. A pulsation suppressor (a pressure regulator)
10. The fuel distributor
11. An atomizer
12. A soaking up collector
13, 20. A lining
14. A collector rack
15. A final collector
16. A thermal guard
17. A rack of the air pump
18. The air pump
19. Gasoline-supply line N2
21. Valves
22. A final collector of a cooling liquid
23. A bar
24. A duplicator
25. Коромысла with platens
26. A cover
27. A sealant

Order of a tightening of bolts of a head of cylinders


The prevention

Works are carried out on the cold engine.


Removal

PERFORMANCE ORDER
1. Remove коромысла and bars.
2. Remove collectors.
3. Remove drive belts.
4. Remove the pump of the hydraulic booster and take aside, without disconnecting a highway.
5. Remove the air pump with an arm (subsection 6.3 see).
6. Remove an air branch pipe (fig. the Head of cylinders of the engine 2F and fig. the Head of cylinders of the engine 3F-E see).
7. Merge cooling liquid, turn out the temperature gauge.
8. Remove the conditioner compressor (if it is provided) and take aside, without disconnecting a highway.
9. In sequence of return specified release bolts (fig. the Order of a tightening of bolts of a head of cylinders see). Cautiously remove a head of cylinders. If the head does not give in to removal cautiously displace its easy blows of a hammer through a wooden pig.

Installation

PERFORMANCE ORDER
1. Clear demountable surfaces of a head and the block of cylinders. Banish carvings of hairpins and apertures.
2. Check up presence on demountable planes of a head and the block of cylinders задиров, having chopped off, hollows and other damages. Check up deformation of a plane of a head. Insignificant damages can be eliminated надфилем, at serious damages the head or the block are subject to repolishing.
3. The lining is executed from a composite material and established without hermetic.
4. Establish a lining an inscription of TORAHS upwards.
5. Cautiously establish a head on the block of cylinders, without breaking lining position. Wrap by hand bolts of a head of cylinders and tighten bolts with the set moment in the specified sequence (fig. the Order of a tightening of bolts of a head of cylinders see).
6. Further assemblage is carried out upside-down. Fill system of cooling with a liquid, fill in oil and replace the filter. Start the engine, be convinced of absence of a leak. Conduct test of road performance of the car.