Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation


Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Kinds of repair without engine dismantle
      3.1.3. Installation of the piston of 1st cylinder in ВМТ
      3.1.4. A cover of a head of cylinders
      3.1.5. A lateral cover of the mechanism timing
      3.1.6. Коромысла and bars of pushers
      3.1.7. Springs of valves, plates, маслосъемные caps
      3.1.8. Soaking up and final collectors
      3.1.9. A head of cylinders
      3.1.10. Pushers
      3.1.11. A pulley коленвала
      3.1.12. A forward epiploon коленвала
      3.1.13. A forward cover
      3.1.14. A cam-shaft and drive gear wheels
      3.1.15. A cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. The oil pallet
      3.1.18. The oil pump
      3.1.19. A flywheel (a leading disk of the hydrotransformer)
      3.1.20. A back epiploon коленвала
      3.1.21. Suspension bracket and engine details
   + 3.2. The verhneklapannyj engine 1FZ-FE
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


122d58df

3.1.8. Soaking up and final collectors
THE GENERAL DATA

Designation of bolts of fastening of collectors on the engine 3F-E

 Bolt And and In on a turn-key basis 17 and 14

With – a nut
The prevention

Works are carried out on the cold engine.

Removal
PERFORMANCE ORDER
1. Disconnect the battery from weight.
2. Merge a liquid from cooling system.
3. Remove the carburettor or the levelling chamber (subsection 5.1.8.3 and subsection 5.2.9.2.6 see).
4. Remove the air pump and an air collector (subsection 6.3 see).
5. Turn away bolts and remove an arm of a final collector.
6. Disconnect a highway from the fuel distributor (on инжекторных engines, subsection 5.2.9.2.5 see).
7. Remove a thermal guard.
8. Remove the pump of the hydraulic booster and take aside, without disconnecting a highway.
9. On cars with automatic transmission disconnect draught of a throttle of transmission.
10. Disconnect a tube recycling (subsection 3.2.4 see).
11. Turn away 2 bolts and 2 nuts of fastening of an exhaust pipe to a collector.
12. Disconnect a socket from the oxygen gauge.
13. Turn away bolts and nuts, remove dividing plugs. Remove collectors.

Installation

PERFORMANCE ORDER
1. Clear planes of the consolidation rests.
2. If the collector varies, rearrange on a new collector all details from the replaced.
3. Establish a new lining and collectors.
4. Tighten bolts and nuts in the specified sequence, with the set moment (the Designation of bolts of fastening of collectors fig. see the engine 3F-E).
5. Establish all removed details upside-down.
6. Start the engine and be convinced of absence of a leak.