Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Kinds of repair without engine dismantle
      3.1.3. Installation of the piston of 1st cylinder in ВМТ
      3.1.4. A cover of a head of cylinders
      3.1.5. A lateral cover of the mechanism timing
      3.1.6. Коромысла and bars of pushers
      3.1.7. Springs of valves, plates, маслосъемные caps
      3.1.8. Soaking up and final collectors
      3.1.9. A head of cylinders
      3.1.10. Pushers
      3.1.11. A pulley коленвала
      3.1.12. A forward epiploon коленвала
      3.1.13. A forward cover
      3.1.14. A cam-shaft and drive gear wheels
      3.1.15. A cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. The oil pallet
      3.1.18. The oil pump
      3.1.19. A flywheel (a leading disk of the hydrotransformer)
      3.1.20. A back epiploon коленвала
      3.1.21. Suspension bracket and engine details
   + 3.2. The verhneklapannyj engine 1FZ-FE
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


122d58df лазерная резка металла в нижнем новгороде

3.1.10. Pushers
THE GENERAL DATA

The worn out pusher (or a cam-shaft cam) is at the bottom "тиканья" at engine work, it can be defined idling listening through a hose piece, or on knock change, having put wooden брусок to working коромыслу at the removed cover of a head of cylinders.

If noise is shown distinctly it is necessary to replace a cam-shaft and pushers.

Removal

PERFORMANCE ORDER
1. Uncover heads of cylinders.
2. Remove коромысло with the platen and get a bar in that cylinder in which pusher work is accompanied by abnormal noise.
3. Remove a lateral cover and get a pusher ().
4. Store pushers as their installation.

Check

PERFORMANCE ORDER
1. Serially wash out pushers.
2. Check up deterioration of a persistent surface of a pusher, a saddle of a bar and a condition of a lateral surface. Replace pushers if on a persistent surface are observed наволакивание metal, scratches or the raised concavity.
3. The persistent surface of a pusher has concavity with the big radius of curvature (on a photo check of concavity of a persistent surface of a pusher at the left is shown). If the persistent surface is worn strongly out (a photo on the right) it is necessary to replace a cam-shaft and pushers. If the lateral surface (that is improbable) check up a condition of apertures in the block of cylinders is worn out. Check up a condition of saddles of bars and end faces of bars.
4. The cam-shaft and pushers vary only together. The removed pushers put on former places.

Installation

PERFORMANCE ORDER
1. Grease pushers молибденовой with greasing.
2. Oil apertures in the block of cylinders for the engine.
3. Establish pushers into place.
4. Establish other removed details upside-down.