Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation

Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
   - 3.1. Engines 2F and 3F-E
      3.1.1. Technical characteristics
      3.1.2. Kinds of repair without engine dismantle
      3.1.3. Installation of the piston of 1st cylinder in ВМТ
      3.1.4. A cover of a head of cylinders
      3.1.5. A lateral cover of the mechanism timing
      3.1.6. Коромысла and bars of pushers
      3.1.7. Springs of valves, plates, маслосъемные caps
      3.1.8. Soaking up and final collectors
      3.1.9. A head of cylinders
      3.1.10. Pushers
      3.1.11. A pulley коленвала
      3.1.12. A forward epiploon коленвала
      3.1.13. A forward cover
      3.1.14. A cam-shaft and drive gear wheels
      3.1.15. A cam-shaft and support
      3.1.16. Replacement of bearings
      3.1.17. The oil pallet
      3.1.18. The oil pump
      3.1.19. A flywheel (a leading disk of the hydrotransformer)
      3.1.20. A back epiploon коленвала
      3.1.21. Suspension bracket and engine details
   + 3.2. The verhneklapannyj engine 1FZ-FE
   + 3.3. Dismantle and engine major repairs
   + 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes

3.1.15. A cam-shaft and support
Check of deterioration of cams

PERFORMANCE ORDER

1. Uncover heads of cylinders.

2. Establish the piston of 1st cylinder in ВМТ a compression step.

3. Check up deterioration of cams on 1st cylinder. For this purpose establish the indicator over the first коромыслом so that the indicator leg passed in parallel an axis of a bar and settled down directly over a bar.

4. Establish the indicator on a zero, turn коленвал in a direction of normal rotation. After indications will cease to change turn коленвал back to an arrow stop. The difference of indications is equal to the size of a cam.

5. Write down indications and again establish the piston of 1st cylinder in ВМТ a compression step.

6. Rearrange the indicator on another коромысло 1st cylinder and repeat measurements.

7. Repeat measurements for other cylinders according to an engine operating procedure (subsection 3.1.1 see).

8. Compare results to the standard. If reduction of the size of a cam owing to deterioration exceeds norm a cam-shaft replace.

Check

PERFORMANCE ORDER

1. Remove a cam-shaft and wash out. Check up a condition of necks. If on necks there are wear tracks are worn out as well cam-shaft bearings. In this case it is necessary to replace a cam-shaft and bearings.

2. If necks in a satisfactory condition check up their diameter in several places, define конусность and ovality.

3. Check up internal diameter of bearings of necks, define a backlash and compare to the standard. If the backlash exceeds norm replace bearings (it is carried out in car-care centre).

4. Check up a condition of a gear wheel of a drive of the distributor of ignition. If there are signs of strong deterioration a cam-shaft replace.

5. Check up a condition of cams, presence on them выкрашивания, задиров and deep development. Check up the sizes of cams a micrometer. If cams in a satisfactory condition and the size corresponds to norm the cam-shaft can be used further.