Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation


Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
- 8. Brake system
   8.1. Technical characteristics
   + 8.2. ABS-system
   8.3. Колодки disk brakes (forward or back)
   8.4. A brake support
   8.5. A brake disk
   8.6. Колодки drum-type brakes
   8.7. The wheel cylinder of brakes
   8.8. The main cylinder of brakes
   8.9. Hoses and hydrodrive tubes
   8.10. Removal of air from a hydrodrive of brakes
   8.11. The vacuum amplifier of brakes
   8.12. Колодки a manual brake of back disk brakes
   8.13. Adjustment of a manual brake
   8.14. A cable of a manual brake
   8.15. The switch of a signal of braking
   8.16. A regulator of pressure of back brakes (dosing out and перепускной the valve)
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes




Ссылки по теме :

Мой парень ебет меня рукой, и снимает на камеру https://m.tnt-porno.ru сначала мне было больно, но потом стало чертовски приятно! 122d58df

8.3. Колодки disk brakes (forward or back)
THE GENERAL DATA
The prevention

Колодки vary only in the complete set on one axis. At clearing колодок a dust and a dirt to delete wiping by rags moistened in spirit or a special liquid, it is forbidden to blow.

Replacement

PERFORMANCE ORDER
1. Turn away a stopper of a nutritious tank of brakes.
2. Release nuts of wheels, lift the car and establish on supports.
3. Remove wheels.
4. Attentively check up a disk condition (subsection 8.5 see).
5. In need of grinding or replacement remove a disk and Pads.
The prevention

At performance of works watch liquid level in a tank, if necessary remove a liquid part.
6. Remove spring скобу a finger.
7. Get the bottom finger Pads.
8. Remove an antinoise spring колодок.
9. On cars till 1991 remove a W-shaped antinoise spring колодок.
10. Get the top finger Pads and remove external колодку.
11. Drown pistons of the external cylinder.
12. Grease a basis Pads with antinoise structure.
13. Grease antinoise overlays.
14. Grease an underside Pads and establish колодку in a support.
15. For cultivation of pistons of a support of back brakes the clamp is required. The clamp heel rests against a platform near to the union, and the screw is rolled, pressing on external колодку.
16. Turn away support bolts.
17. Remove a support of a back brake, take a support aside and fix.
18. Remove Pads from a support arm.
19. Get indicators of deterioration and an antinoise overlay and rearrange on new колодку. At detection of deterioration or deformations replace these details new.
20. Remove persistent plates колодок and check up. At detection of the slightest deformations replace.
21. Establish new колодку, an antinoise overlay and the deterioration indicator.
22. Grease overlays external and internal колодок with antinoise structure and establish a support upside-down.
23. At dismantling of a back brake remove basic plates колодок with which it is necessary to replace at their slightest deformation. Rearrange the deterioration index for the thickness new колодок. At damages indicators replace.
24. At assemblage tighten bolts of a support with the set moment.
25. Press some times a brake pedal, check up and restore liquid level in a tank.
26. Check up work of brakes.