Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. Engines
+ 3.1. Engines 2F and 3F-E
- 3.2. The verhneklapannyj engine 1FZ-FE
3.2.1. Technical characteristics
3.2.2. Kinds of repair without engine dismantle
3.2.3. A cover of a head of cylinders
3.2.4. A soaking up collector
3.2.5. A final collector
3.2.6. Cam-shafts and pushers
3.2.7. A head of cylinders
3.2.8. A cover of a chain drive of cam-shafts
3.2.9. A forward epiploon коленвала
3.2.10. The oil pallet
3.2.11. The oil pump
3.2.12. A flywheel (a leading disk of the hydrotransformer)
3.2.13. A back epiploon коленвала
3.2.14. Suspension bracket and engine details
+ 3.3. Dismantle and engine major repairs
+ 3.4. An engine electric equipment
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
+ 8. Brake system
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes
|
Details of the oil pump
1. The pump (a forward cover)
2. A spring
3. Заглушка
4. A lining
5. The reduktsionnyj valve |
6. A lining
7. A conducted rotor
8. A leading rotor
9. A pump cover
10. An epiploon коленвала |
Removal
| PERFORMANCE ORDER |
| 1. Remove belts and a roller натяжителя. |
| 2. Remove the pallet. |
| 3. Remove a pulley коленвала and a forward cover. |
|
4. Turn away 7 screws (are specified by arrows) and remove the case of the oil pump. |
| 5. Remove from demountable planes of the pump and the block of cylinders the consolidation rests, wash out planes solvent. |
| 6. Get leading and conducted rotors. |
| 7. Disassemble редукционный the valve. Заглушку turn out cautiously, holding with effort, as a valve spring very rigid. |
|
Check
| PERFORMANCE ORDER |
| 1. Wash out all details in solvent, check up presence of deterioration and damages. |
| 2. Check up a condition of a sliding surface of the piston редукционного the valve and a spring. At detection of damages the piston complete with a spring replace. |
|
3. Check up probeом a backlash between a conducted rotor and the case.
|
|
4. Check up a face backlash between a rotor and a cover.
|
|
5. Check up a backlash in gearing of rotors.
|
| 6. If backlashes exceed norm rotors in the complete set replace. If necessary replace the pump case (a forward cover). |
|
Installation
| PERFORMANCE ORDER |
| 1. Oil rotors for the engine and establish in the case. |
| 2. Put in a pump cavity technical vaseline, lay a lining, put a cover and tighten screws. |
| 3. Grease the piston редукционного the valve with fresh oil for the engine and establish valve details. |
| 4. Establish a new lining of a cover of a chain on directing pins. |
|
5. Replace a lining of the oil channel of a cover. |
| 6. Establish a chain cover, having entered a leading rotor of the oil pump into gearing with a leading gear wheel коленвала. |
| 7. Establish other details upside-down. |
| 8. Fill in oil, start the engine, be convinced of absence of leaks. |
|
|
|
