Toyota Land Cruiser

FJ60, FJ62 and FJ80 1980-1997 of release

Repair and car operation



Toyota Land Cruiser
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. Engines
+ 4. Systems of cooling, heating
+ 5. Fuel and exhaust systems
+ 6. System of decrease in toxicity
+ 7. Transmission
- 8. Brake system
   8.1. Technical characteristics
   + 8.2. ABS-system
   8.3. Колодки disk brakes (forward or back)
   8.4. A brake support
   8.5. A brake disk
   8.6. Колодки drum-type brakes
   8.7. The wheel cylinder of brakes
   8.8. The main cylinder of brakes
   8.9. Hoses and hydrodrive tubes
   8.10. Removal of air from a hydrodrive of brakes
   8.11. The vacuum amplifier of brakes
   8.12. Колодки a manual brake of back disk brakes
   8.13. Adjustment of a manual brake
   8.14. A cable of a manual brake
   8.15. The switch of a signal of braking
   8.16. A regulator of pressure of back brakes (dosing out and перепускной the valve)
+ 9. Suspension brackets and a steering
+ 10. A body
+ 11. An electric equipment
+ 12. Electroschemes


122d58df

8.6. Колодки drum-type brakes
THE GENERAL DATA

Party installation Pads And


1. The left wheel
2. The right wheel
3. To a forward part of the car

Position колодок after assemblage

1. The left wheel
2. The right wheel
3. To a forward part of the car

The prevention

Колодки vary only in the complete set on one axis.


Together with колодками coupling springs which, being exposed to periodic thermal loadings vary also, gradually lose elasticity and do not provide sufficient tap Pads from a drum. As a result the drum touches for Pads, causing their premature deterioration.

Replacement

PERFORMANCE ORDER
1. Release nuts of wheels, lift back (or a lobby) a car part.
2. Remove wheels.
3. Release a manual brake.
4. Designate drum position, turn away screws (if are provided) and remove a drum.
5. If the drum does not give in to removal fill in between hairpins of a flange of a semiaxis and drum apertures a getting liquid and обстучите a drum from the inside on a contour.
6. If this measure does not give result reduce Pads.
7. For this purpose on brakes with a horizontal arrangement колодок get заглушку from a board of a brake and rotate a cogwheel of a regulator a screw-driver.
8. On brakes with a vertical arrangement колодок take away a screw-driver with a narrow edge the lever of a regulator from a cogwheel and rotate a cogwheel of a regulator other screw-driver.
Brake with horizontally located колодками
9. Remove a coupling spring.
10. Remove clamping springs колодок, having pressed a cup and having turned on 90 °.
11. Remove Pads together with the bottom spring.
12. Grease rubbing surfaces Pads from outside a board with refractory greasing and establish Pads upside-down.
13. The party Pads And establish according to fig. party Installation Pads And.
Brake with vertically located колодками
14. Remove the top spring.
15. Remove a clamping spring, having pressed a cup and having turned on 90 °, and remove back колодку.
16. Disconnect a clamping spring and remove a lobby колодку in gathering with a regulator. Get flat-nose pliers a cable of a manual brake from the lever.
17. Remove from a lobby Pads a spring of the lever of a regulator.
18. Remove a regulator.
19. Remove a lock washer and get the regulator lever.
20. Remove скобу and remove the lever of a manual brake.
21. Establish on new a lobby колодку the lever of a manual brake and press out скобу. Establish the lever of a regulator and a cutting lock washer (a washer and скобу replace).
22. Grease rubbing surfaces Pads from outside a board with refractory greasing.
23. Grease details of a regulator with refractory greasing, screw a regulator hairpin in распорку.
24. Establish Pads upside-down.
25. Position колодок after assemblage дожно to look definitely (fig. Position колодок after assemblage see).
26. Clear a drum and check up a surface condition.
27. Check up ovality of a drum, at strong damages a drum pierce, small roughnesses are ground by a skin.
28. If after проточки internal diameter of a drum appears more limiting (it is specified on a drum), a drum replace.
29. Establish a drum and check up brake adjustment.
30. If the backlash between колодками and a drum is too great, remove a drum and rotating a hairpin wheel dissolve Pads to a contact of a surface of a drum.
31. Reduce Pads that they did not touch a drum (it is checked on hearing) a little.
32. Establish a wheel and lower the car.
33. Make some braking, moving forward and a backing.
34. Before departure check up work of brakes.